When you bought a new expensive headphone and accidentally broke it. And the most common problem is having a loose connection, you may be tired of having to twist your headphone wire to a certain position just to hear sound right?
How To Fix Broken Headphones?
But there are simple ideas to fix your headphones back on your head where they should be in no time. So here in this article, we will help you to find different guidelines on how to fix broken headphones in case they have the fixing potential. Let’s check out.
Causes of Broken Headphones
There are some common headphone failures, which includes:
- Electrical short in the wires that transmit sound.
- Malfunctioning earpiece.
- Defective jack plug.
- Audio jack problems.
To fix your headphones, you must identify the source of the problem. So here are some tips to help figure out why your headphones aren’t working:
- If the sound of your headphone is cutting in and out. And if you can listen well when the cables are positioned in a certain way, then it’s an electrical short issue.
- If you hear the sound when you gently push the plug into the audio jack, then you need to fix the plug.
- If you don’t find any audio while listening then it’s time to fix the headphone jack itself, which is an entirely different topic.
- If one side has no audio and the other side has audio, you need to fix the earpiece.
Best Ways To Fix Cable On Corded Headphones
- The most important thing you have to do is to find the place on the headphone’s cable where the break has happened. To find the break all you have to do is put the headphones on and bend the cable 90 degrees across your thumb. When you find the location of the break, mark the point with electrical tape.
- Now i’s time to fix the mid-cable break, so for that, it’s important to slide the shrink tube and remove the half-inch of shielding by using a knife.
- After that, you need to splice the wires, but there are two common types of wire splices, in-line and pigtail. To create a Pigtail splice, hold the two exposed sections and join them parallel to each other and twist them to make a join. It is much easier than In-Line splicing.
To create in-line splices hold the wires that will overlap from one end to another. So you should twist wires in the opposite directions because that will create a strong joint that will fit the natural direction of the cable. It is quite difficult to complete, but after the hassle, you’ll get a better sound.
- Now it’s time to use the soldering tool, when you complete the joins, let them cool. At the same time make sure to wrap two pairs in the electrical tape. This is because there is a chance to separate them from earth wire. After that place, the shrink tube on the two-taped section and apply heat. This helps the tube to shrink down to a quarter of the original size which means you will be able to fit it and strengthen the cable that you repaired moments ago.
What did You need to Fix Broken Headphones?
- Scissors or a sharp blade
- Wire strippers
- Electrical or duct tape
- A lighter
- The third hand with alligator clips
- Solder and a soldering iron
Fix Headphones Without Tools
- When you twist, bend, straighten and adjust the cord, you might hear the audio as well as the damaged wires. You can use this strategy to determine where the loose connection is.
- After you find a position that allows you to hear the sound, hold it with your fingers. Continue holding on to the cable until you wrap electrical or duct tape around the short.
- If it’s done properly, then you should compress the cable enough to keep the wires touching.
Also, read Top 10 Most Durable Headphones in 2021
Fix a Short in Headphones
- Identify the site and mark it with a permanent marker or piece of tape.
- Now carefully strip the surrounding by using wire strippers or a knife to expose the broken wire.
- And then cut the cord in half, severing any intact wires. But make sure to make an even cut so the wires are the same length.
- Strip off the cables to expose more wires and then sort the wires by colour.
- Join the two sides of each wire and hold the two ends of each wire parallel and twist them together.
- Then, solder the spliced wires and allow them to cool.
- Once the wires are connected, tightly wrap the exposed area by using electrical tape.
From the above article, you’ve found the most common problems that happen for both Wireless and Wired Headphones. So hope you liked this article and found some ideas to keep your headphones safest as possible, and helped to find a solution that will keep the money in your pocket for future purchases.